Show Details

 

What're your concepts on How to Install a Bathtub?

Setting up a bathtub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably challenging job. If the old bathtub is conveniently available, the task can move speedily; if you need to open up a wall to get rid of the old tub and also place the new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's abilities, although you will require an assistant to move out the old bathtub and also set in the brand-new one. Ensure you have qualified on your own for the task and are comfortable trying it. As opposed to hiring a contractor to take over a halfway-completed job, it is much better to think about employing one before you start. Possibilities are you might need an expert plumber to make tube connections.
This post will aid you mount a new tub in your shower room if you have actually currently purchased a new bathtub as well as do not need to transform the plan of your previous water supply pipelines.
Your tools and also material list ought to make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you require to change old taps with new ones as a part of your setup, after that the first thing you ought to do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome as a result of the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
Before going on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

 

 

Suitable New Touches

If the tails of the new taps are plastic, after that you will need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former type needs to be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Installing the Bath tub

Utilizing both wood boards under its feet, place the bathtub in the needed setting. The wood boards are practical in equally spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bath tub until the spirit level reads level.
To mount taps, fit all-time low of the furthest flexible tap connector to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Turn on the water system as well as inspect all joints as well as new pipework for leaks and also tighten them if essential. Load the tub and also check the overflow electrical outlet as well as the normal outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub should wait up until the bathtub has actually been used at the very least once as this will certainly settle it right into its final placement.

 

 

Preparing for the Installation

First of all, the supporting frame supplied with the bathroom must be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to stop strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its last position.

 

 

Tiling Around the Bath tub

In the area where the bathroom fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break a stiff seal, causing the water to pass through the wall surface between the bath as well as the tiling, bring about difficulties with wetness as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, and can securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water resistant glue and also cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I'm very taken with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you enjoyed my blog entry. Enjoyed reading our write up? Please share it. Let others find it. We appreciate reading our article about How to Install a Bathtub Yourself.

Request immediate service.